Specifically designed to provide optimal adhesion of UV curing inks without adhesion promoters, OPTIX DA delivers all the benefits of continuously processed acrylic sheet in a specially formulated product for printing. Just as with OPTIX sheet, OPTIX DA provides superior strength and is available in a variety of sizes and thicknesses. It is the ideal choice for insulating mechanical piping systems. For applications requiring fire and smoke ratings of 25/50, AP ArmaFlex FS (Flame Spread)meets ASTM E 84 at 25/50 for 1-1/2” and 2” thicknesses. Both may be used on a variety of curved or flat mechanical surfaces such as large pipe, ducts, tanks, chillers, etc.
UL-723, ASTM E-84 & ULC-S102 ASTM E-814, UL 1479 or ULC S115 230ºF (110ºC) 248ºF (120ºC) 0 at 230ºF (110ºC) Pass 12.5 kPa / H1 @ 20 kPa Min. 101 lb force (.45kg) with Connector Rings <25 / <50 with recommended wrap 2hr with recommended pas-sive fire protection system Low Temperature Handling UL-1738 Pass at -4ºF (-20ºC) Aerocel Pipe lnsulation in 3/8″, 1/2″, 3/4″, 1″, 1-1/4″, 1-1/2″ and 2″ thicknesses has a flame spread rating of 25 or less and a smoke developed rating of 50 or less as tested by ASTM E 84 “Surface Burning Characteristics of Building Materials.” www.metrosupplycollc.com
Most building codes require a maximum 25/50 (flame spread/smoke development) rating for a material used in an air handling plenum or as duct or air handling equipment liner. Rating is typically required at the thickness used. These areas are the most stringent requirements, with lesser ASTM E 136 (Noncombustible) (Unfaced) ASTM E 84 (Flame/Smoke 25/50 or less) X X X 1. When ordering material to comply with any government specification (or any other listed specification), a statement of that fact must appear on the purchase order. 2. Exceptions to ASTM standards: Not tested for compression resistance.
Universal Building Code (UBC) Requirements for CH8 and CH26 What is the flammability rating, Class I, Class II, or Class III, of ACRILEX, INC.'s acrylic products in accordance with building codes (BOCA, ICBO, or SBCCI) specifically in Chapter 8 "Interior Finishes"? [email protected] fitting covers will be labeled on the box 'Passes ASTM E- 84.11 Flame spread 25; smoke developed 50". All E-84 ratings shown here were tested on flat sheets from which fitting covers are made. Virtually all Proto [email protected] fitting covers will pass E-84 25/50 flame spread and smoke development rating requirements. TM Engineered ...
Flame Spread ASTM E84 25 or less Smoke Developed ASTM E84 50 or less Thermal Conductivity (75°F/24°C) ASTM C177 0.26 Specification Data Hot Systems All piping fittings shall be insulated by filling the total void over all fittings, between straight runs of pipe insulation, with Speedline® die-cut fiberglass "This product does not meet the 25 Flame/450 Smoke index material test standard ASTM E-84, and may not satisfy City County, or State Code enforcement bodies. Check with your Authority Having Jurisdiction (AHJ)." P-Trap Cover, Valve and Supply Cover P-Trap Full-Rotation Option (Two-Piece Installation) Inner-Ring Grip Structures Integrated ...
ASTM E 136 (Noncombustible) (Unfaced) ASTM E 84 (Flame/Smoke 25/50 or less) X X X 1. When ordering material to comply with any government specification (or any other listed specification), a statement of that fact must appear on the purchase order. 2. Exceptions to ASTM standards: Not tested for compression resistance. FESCO ® Board Perlite-Based Cover Board Refer to the Safety Data Sheet and product label prior to using this product. The Safety Data Sheet is available by calling (800) 922-5922 or on the Web at The ASTM e84 fire test method is designed to show comparative measurements of surface flame and smoke development of exposed building materials such as walls an
performance and an E-84 Class A surface that may be left exposed. Composition and Materials: The product is composed of glass fibers bonded together with a thermoset binder. docs.wixstatic.com Both standards require material in duct, plenums, and other air handling space to have been tested by ASTM E 84 or UL 723, and be rated at flame spread of 25 or less and smoke developed of 50 or less. These standards require the service temperature MUST be 250°F MINIMUM, or greater, continuous use temperature.